What gun stuff did you do today?

[bohica793]

Just send me the 5.56 BCG Frank. I'll find a use for it. I would hate for you to be tempted to fall back into bad habits.

 

[FrankT]

yeah me too, what are they worth now $300? like that green tip ammo?

 

[Khaot1c]

Ranger Firearms in Fort Walton has Bullseye, HP-38, and IMR4227 on the shelf. Going for $32/pound.
Glad 1# will load a LOT of rounds.

 

[bohica793]

Poured 300 9mm 147gr. Had to break for lunch. Will probably go pour another 3-400 this afternoon. Need to load these and some 45ACP tonight.

 

[John B.]

Ordered 2 sets of 45° iron sights off Amazon, as well as a Burris PEPR 30mm mount and a Weaver kaspa 1-6 scope for my .300 Blackout pistol.

Sent from my Galaxy S5....

 

[John B.]

Drove by TGD and ended up leaving with a lighter wallet.

Sent from my Galaxy S5....

 

[madeSICC88]

Been needing to get a grip sleeve or something for my XD as the grip pads have worn down pretty good over the last 3-4 years and are pretty slick so I thought I'd try to make my own first for fun. I didn't want to use grip tape since I carry this gun and I couldn't find any rubbery friction tape so I thought I'd try the canvas kind, it adds a good amount of grip but I don't think it will be very resilient. I heated it up pretty good to try and make it bond but I don't have high hopes for it.

 

[John B.]

Sent from my Galaxy S5....

 

[madeSICC88]

You putting a longer muzzle device on that pistol?

 

[Clay]

Too late for this deer season, but just got my new 308 rig set up. Remington 700 SPS w/ 16.5" threaded barrel and Hogue Ghillie stock,Vortex 6-18x44 scope, Weaver 20MOA one piece mount and Vortex rings. JP muzzle brake will be here this week. Will be thumping some hogs and Yotes in the near future.

 

[John B.]

You putting a longer muzzle device on that pistol?

I plan on it... it just has a birdcage on it now and is recessed about half an inch from the end of the rail... I think I'm going with a Noveske KX5 to get the length out there...

Sent from my Galaxy S5....

 

[gunnerxxx]

Ordered more reload supplies. reloaded some 300 weatherby rounds for a friend. and repaired a buddys Remington 7400.

 

[bohica793]

Go to Lowe's or Home Depot and pick up a piece of peel and stick stair tread material. You can cut it to fit the grip and it works amazingly well.

Been needing to get a grip sleeve or something for my XD as the grip pads have worn down pretty good over the last 3-4 years and are pretty slick so I thought I'd try to make my own first for fun. I didn't want to use grip tape since I carry this gun and I couldn't find any rubbery friction tape so I thought I'd try the canvas kind, it adds a good amount of grip but I don't think it will be very resilient. I heated it up pretty good to try and make it bond but I don't have high hopes for it.

 

[TennJeep1618]

madeSICC, I've got lots of skateboard tape if you want to give it a shot. It's pretty rough, but you're welcome to try it.

 

[bohica793]

madeSICC, I've got lots of skateboard tape if you want to give it a shot. It's pretty rough, but you're welcome to try it.

That stuff is pretty much the same as stair treads.

 

[TennJeep1618]

That stuff is pretty much the same as stair treads.

Yeah, it's thicker and more coarse than Talon grips, but it works pretty well for my uses.

 

[jogan]

^ if only it made you a little faster....just a few hundredths faster....

 

[madeSICC88]

I don't really want to use anything that coarse, i am going to order a rubberized kit from eBay or the kit they sell on PRP.

 

[madeSICC88]

^ if only it made you a little faster....just a few hundredths faster....

Sounds like fightin words

 

[TennJeep1618]

Sounds like fightin words

He's just mad because it only took me about 6 months to catch up to where he is after a couple years.

Sent from my SAMSUNG-SGH-I747 using Tapatalk