Stuck Case Help!!!!!

Clay · Jun 28, 2015

I shot my PA 10 today. First shot, didn't go off. Thought perhaps I had a bad primer, ejected the shell and next four rounds went off perfectly, had used a laser bore sighter found zero after four rounds. Fifth shot, nothing. Also stuck and had to mortar it to free it up. Upon inspection I see the following, a burr? The four ejected shells all had this gouge in casing. I believe the first shot didn't load all the way thus no ignition.

Going to take it to Copeland's tomorrow but just curious as to the experts and your thoughts, brand-new from PSA clearly I can send back but is this an easy fix with the Dremel and buffing out what appears to be a burr?

Thanks Guys!

ImageUploadedByTapatalk1435525795.465003.jpg

ImageUploadedByTapatalk1435525806.500517.jpg

ImageUploadedByTapatalk1435525814.955086.jpg

bohica793 · Jun 28, 2015

I vote send it back. While you could buff that out with a dremel, if you screw it up you may get gas blowback and them be stuck with replacing it at your own expense.

Little Jack · Jun 28, 2015

I'd send that back too. The wait sucks but if you booger it up your on your own.

Clay · Jun 28, 2015

Thanks guys, I will be sending it back

Crazydoc68 · Jun 29, 2015

Clay said:
Thanks guys, I will be sending it back

I had to send mine back for same issue. Took about a months turn around. Psa knows about this issue yet they are still selling them with no QC. If they know they have thos issue with many, if not all of their 308 platforms, why dont they figure it out before sellimg them and them have the customer have to send it back to them. That shit pisses me off.

Doc

ChrisC · Jun 29, 2015

minor issue. not worth the shipping and wait time.

wrap a .308 case with a sandpaper (I'd use 400 grit). sand the burr down with strokes parallel to the feed ramp. go easy and take your time. change to finer sandpaper to even out and finish off with a buffing wheel on a dremel. I would not use a dremel to remove the burr.

Clay · Jul 23, 2015

Got my upper back today, shipped it back on the 6th, arrived 8th and shipped back on the 21st. Not thrilled I had to ship it back, but happy they got it back to me in two weeks time. Apparently the barrel tolerances were too tight. Got a new BCG and affirmation that it's GTG. Ready to pop some piggies after checking it at the range.

ImageUploadedByTapatalk1437683550.282597.jpg

MAXman · Jul 23, 2015

Let us know if it's unfouled.

If doc is right and this is a known issue, on top of you paying shipping... That's kinda poor in my opinion.

Clay · Jul 24, 2015

MAXman said:
Let us know if it's unfouled.

If doc is right and this is a known issue, on top of you paying shipping... That's kinda poor in my opinion.

I will let ya know. They provided UPS shipping label. It sucks, but didn't cost me anything but time and as Enforcement Firearms is also a UPS shipping location, it wasn't a big deal for me, but for others I'm sure it would be a pain in the ass. I agree, they could easily check this prior to shipping, even upon receipt of the barrels pre-assembly

Viking1204 · Jul 24, 2015

Hopefully the individual who repaired it submits paperwork for an improvement process and in future they do check it.

Please read the new forum rules! REQUIRED!

Click Here: https://www.gulfcoastgunforum.com/threads/general-forum-rules-code-of-conduct.70770/

Stuck Case Help!!!!!

The #1 community for Gun Owners of the Gulf Coast States

Member Benefits:

Clay

Master

Attachments

bohica793

Master

Little Jack

Master

Clay

Master

Crazydoc68

Almost a doctor

ChrisC

Master

Clay

Master

Attachments

MAXman

Master

Clay

Master

Viking1204

Master

Latest posts

Members online

Forum statistics

Share this page